2 way remote light switch, push button switch philippines,buy best Livolo Glass Intelligent Touch Switch Panel Single Control Home Light sale,
To convert To convert A Pull String Light To A Wall Switch
Is usually is usually challenging to seek out the pull string to activate a light in a dark room. There isn’t any telling what you might bump into before getting the lights burning. Pull chain switches normally wear out long before the sunshine fixture. The sunshine may be converted to operate from a wall switch whether the pull string has stopped working, or you are uninterested in flailing around at nighttime. Install a straightforward-to-find light switch to operate the ceiling light for years of reliable service.
Things You may Need
Remodel electrical wall box
Romex cable 12/2
Black electrical tape
Select a location on the wall for the switch. Run a stud finder from that location as much as the ceiling to make certain there aren’t any obstructions behind the wall that will block a cable from the reaching the placement.
Shut off power to your complete house by turning off the “main” switch within the breaker panel. Leave a warning sign or lock the breaker box to make sure that the power stays off until you finish.
Draw a pencil mark around the paper wall pattern supplied with the wall box, or an overview of the back rectangular shape of the remodel wall box. Cut through the drywall along the lines with a drywall saw.
Place one end of a 2/12 Romex near the ceiling light within the attic with 12 inches of excess cable available for making connections. Drape the cable along the rafters from the light to the wall that may hold the switch. Attach the other end of the Romex to the hook of a fish tape and secure it with electrical tape. Push the fish tape down the wall from the ceiling to the newly cut opening within the drywall. Push 18 inches of cable through the opening.
Slice through the plastic outer jacket of the Romex with a utility knife lengthwise to make an 8-inch slit at the top within the attic, and the top within the wall opening. Slice off the slit portion of the jacket to free 8 inches of the inner wires. Strip the insulated wires with wire cutter blades to expose 1/2 inch of bare wire at each end. Strip the wire ends in the attic near the sunshine and push button switch philippines on the wall switch location. Wrap 1 1/2 inches of black electrical tape around the white wire of the Romex at both ends just behind the bare wire.
Feed the wires on the light switch end in through the cable hole within the wall box. Recoil the push button switch philippines holding clamps on the wall box by pushing them toward the back, or inward depending on the wall box manufacturer. Hold the clamps as you insert the box into the outlet within the wall. The clamps will spring back into place to create pressure between themselves and the outer frame of the wall box in front of the cut opening. Tighten the clamp screws to create a firm grip on the drywall and secure the wall box.
Connect the black wire from the Romex to one of many terminals on the switch, and the white wire wrapped in black electrical tape to the opposite terminal by winding the bare wire across the terminal screws in clockwise rotations. Tighten the terminal screws with a Phillips screwdriver. Connect the bare copper ground wire from the Romex to the ground terminal screw within the back of the wall box.
Other Individuals are Reading
How to repair a series That Pulled Out on a Ceiling Light
How to fix a Pull-Chain Light Switch
Unscrew the mounting screws holding the sunshine fixture to the ceiling. Unscrew the terminal on the sunshine socket holding the black wire. Twist the bare wire from the removed black wire across the bare wire of the black Romex wire within the attic. Cap the reference to a wire nut by twisting it over the exposed wire with clockwise turns.
Connect the white Romex wire marked with black electrical tape to the terminal on the sunshine socket that formerly held the black wire. Cut the bare copper, or green ground wire about 8 inches from where it connects to the sunshine. Strip 1/2 inch off the insulation at both freshly cut ends of the wire if it is wrapped in green insulation. Twist the two wire ends across the bare copper ground wire of the Romex and canopy the connection with a wire nut.
Check all wire connections to be sure every color-coded wire is connected to the proper terminal. Replace the ceiling lamp and tighten the holding screws. Place the light switch contained in the wall box and tighten the mounting screws with a Phillips screwdriver. Place the cover plate over the switch and secure it with the holding screws. Tighten those screws with a slotted screwdriver. Restore power and operate the light with the brand new switch.
Tips & Warnings
Don’t perform your personal electrical work unless you’re trained or experienced in household electric wiring. Serious damages and injuries can occur when electric wires will not be connected correctly.
Self Help and More: Converting pull-string light to wall switch
Renovation Headquarters: Installing a light switch
Make My very own House: Diagrams for light switch wiring
Photo Credit Lamp image by Ivan Zhupanov from Fotolia.com
Promoted By Zergnet
push button switch philippines