Press "Enter" to skip to content

remote switch raspberry pi,capacitive touch switch circuit

admin 0

touch screen wall switch, remote switch raspberry pi,Buy 2 Ways Wireless Remote Control Light Touch Switch Spectrum,

DTMF Controlled Home Automation System Circuit

Easy methods to Operate the Circuit
Advantages of DTMF Controlled Home Automation System Circuit:

Wireless Touch Switch Gold 3 Gang 1 Way Glass Light SwitchesNo security. Anyone can control the appliances by calling the mobile connected to module.
Variety of appliances is restricted as our mobile can generate only 16 tones.
Generally, appliances used in our home are controlled with the assistance of switches. Nowadays, you’ll be remote switch raspberry pi able to see automation of those appliances using many technologies. This article presents the controlling of home appliances using DTMF technologyDTMF is acronym for Dual Tone Multi Frequency. So, just think whenever you make call for customer care, they will ask you to press 1, 2 or some other number. Once you press a number from your mobile, one particular action is occurring. All that is due to DTMF. When a button is pressed in your mobile keypad, it should generate a tone of two frequencies. These tones are called row and column frequencies.

Generally, row frequencies are low frequencies and column frequencies are high frequencies. These frequencies for DTMF are chosen in such a way that they don’t have harmonic relation with the others, in order that they will not produce same tones. The column frequencies are slightly louder than the row frequencies to compensate for the high-frequency roll off of voice audio systems.
Related Post: DTMF Controlled Robotic Vehicle without using Microcontroller

We have learned that each button pressed in keypad will produce a tone which differs from others. Now we should always use these tones for our appliances. So this DTMF encoder is present in mobile. Output from keypad can be converted into digital form using DTMF decoder IC HT9107B. Interfacing of this IC to MCU is show below.
DTMF Controlled Home Appliances Circuit Principle:

The main principle of this circuit is to regulate appliances like light and fan using DTMF technology. DTMF encoder is present in your mobile and decoder is HT9107B IC. Mobile jack is connected at 1nf capacitor. Mobile jack consists of two wires (Red and black). Red wire is connected to the decoder IC and Black is grounded. When a button is pressed from mobile it generates a tone which is decoded by the decoder IC and it is shipped to ATMEGA8 controller. Controller then checks for input and it produces the output in response to the code written to it.
DTMF Controlled Home Automation System Circuit Diagram:

DTMF Based Home Automation System using Microcontroller Circuit Diagram
Circuit Components:
This circuit mainly consists of the next components.
ATmega8 microcontroller U1
HT9107B IC
Relay
AC Load
Resistors – R1, R2 and R3
Capacitors remote switch raspberry pi – C1, C2, C3 and C4
Crystal Oscillator X1

Circuit Design of DTMF Controlled Home Appliances:
The decoder IC consists of an inbuilt operational Amplifier. The output of op-amp is given to the pre-filters to separate low and high frequencies. Then it’s passed through frequency and code detector circuits, thus 4-bit binary code is latched.
Tone from mobile is shipped to op-amp through series of resistor (100 kilo-Ohm) and capacitor (1nf). Pin1 of DTMF IC i.e. non inverting pin is connected to pin4 i.e. Vref. Pin3 is the output of operational amplifier which is feedback to pin2 using 100 kilo-Ohm resistor. 7 and 8 pins are connected to crystal oscillator of frequency 3.579545 MHz. 15th pin is data valid pin it becomes high when DTMF tone is detected else remains low. The technique of frequency detection to digitalization of the signal is finished by steering circuit consisting of EST, RT/GT, and resistor (10k), capacitor. Pins 11 to 14 produce the decoded output.
Related Post: Cell phone Controlled Home Appliances without using Microcontroller

The output pins of DTMF IC (i.e. 11 – 14) are connected to PB0-PB3 pins of controller. Output pins of the controller i.e PD0 and PD1 are connected to relay. Relay output is connected to AC source i.e. light or fan.
Relay acts as a switch. It produces isolation from different parts of the circuit. In our project it’s used to switch AC load using 5v which is maximum voltage from controller. Relay used here is magnetic relay.
Tips on how to Operate the Circuit

When the circuit is powered, controller continuously checks the inputs. When ‘1’ is pressed from mobile keypad, decoder IC decodes the tone and produces 1(0001), it’s given to microcontroller which in turn produces high output at PD0 pin. PD0 is connected to relay. Relay is used for switching the circuit and thus fan is ON. Similarly, if the received input is 2 fan is switched off. If received input is 3 light is switched on and whether it is 4, light is off.
Advantages of DTMF Controlled Home Automation System Circuit:

One can control home appliances from anywhere.
It reduces wastage of electricity once we forgot to switch off the lights & fans and gone outside.
It is very low cost in comparison with other technologies like GSM.
Limitations of DTMF Controlled Home Appliances:

No security. Anyone can control the appliances by calling the mobile connected to module.
Variety of appliances is restricted as our mobile can generate only 16 tones.

remote switch raspberry pi

Leave a Reply

Your email address will not be published. Required fields are marked *